10.9S Heavy Hex Structural Bolt GB/T1228 For Steel Bridge & Tower

10.9S heavy hex structural bolt GB/T1228 black HSFG bolt with nut and washers
Black Phosphorus
Zinc Plated
Mechanical Galvanizing
Hot-dip Galvanizing

A 10.9S heavy hex structural bolt is a high strength friction grip bolt (HSFG bolt) designed for friction-type connections in steel construction. We supply grade 10.9S heavy hex structural bolts to GB/T1228, matched with high strength nuts and washers to form one complete bolt assembly for steel bridges, tower structures and heavy steel frames. The black phosphate finish protects the alloy steel core, and the controlled pre-tension of each bolt transfers load through friction between connected steel plates rather than through bolt shear.

Key Features of 10.9S Heavy Hex Structural Bolt

A 10.9S heavy hex structural bolt uses a larger hex head and a shorter grip than ordinary bolts, giving a bigger contact area with the washer. This design spreads the clamping force evenly across the faying surface and prevents the connected plates from slipping under dynamic load. The 10.9S grade reaches high tensile strength and guaranteed pre-tension, so engineers can rely on a consistent clamp in every joint.

Each 10.9S heavy hex structural bolt leaves the factory with black oxide or black phosphate finish, heat treated to the required tensile strength and hardness. We mark the grade and standard on the head so inspectors can identify the grade at site.

Materials and Grades

We produce structural bolt assemblies in two main grades:

  • Grade 10.9S: alloy steel 20MnTiB, 35VB or 40Cr, quenched and tempered for high pre-tension capacity
  • Grade 8.8S: carbon steel 35# or 45#, for lighter steel structures and secondary components

The 10.9S material uses 20MnTiB or 35VB for better hardenability and notch toughness, which is essential for main load-bearing joints in high-rise buildings and steel bridges. The 8.8S version uses 35# or 45# carbon steel and offers a more economical solution where loads are lower.

Dimensions and Standard Assemblies

Our 10.9S heavy hex structural bolt covers the common diameters M16, M20, M22, M24, M27 and M30. Lengths range from 50 mm to 130 mm, in steps of 5 mm up to 100 mm, then 110 mm, 120 mm and 130 mm. We can cut non standard lengths to your drawing for special joint configurations.

Every full assembly follows three Chinese standards:

  • GB/T1228: dimensions of the heavy hex structural bolt
  • GB/T1229: the matched high strength nut
  • GB/T1230: the matched high strength washer

One complete assembly includes 1 bolt (GB/T1228), 1 nut (GB/T1229) and 2 washers (GB/T1230). Supplying them as a matched set avoids mixing hardness levels and keeps the joint properties as designed.

Friction-Type Connections

A 10.9S heavy hex structural bolt works differently from ordinary shear bolts. When tightened to the specified pre-tension, the clamp compresses the connected steel plates together. The load then transfers through friction on the contact surfaces, not through the bolt shank or bearing. This slip-critical behaviour gives the joint better fatigue resistance under vibration and repeated loads.

For the friction to work, the faying surface must be clean and properly prepared. We supply test reports on request so your engineer can verify the bolt pre-tension, hardness and surface condition. You can read more about the working principle on the bolted joint guide.

Applications in Steel Construction

Grade 10.9S heavy hex structural bolts are specified for main load-bearing steel joints in:

  • Factory structures and industrial steel frames
  • High-rise steel building columns and beams
  • Steel bridges and bridge girders
  • Power transmission towers and telecommunication towers
  • Steel trusses and large span roof structures

Grade 8.8S suits light steel structures and secondary components such as purlins, bracing and wall girts, while grade 10.9S is reserved for the primary moment and shear connections that carry the design loads.

Custom Service and Why Buy From Us

Besides standard 10.9S and 8.8S assemblies, we can customize grade 12.9S heavy hex structural bolts with other surface treatments, materials and dimensions. We hold regular stock of M16 to M30 assemblies and ship trial orders quickly, and we accept OEM orders with head marking and packing to your requirement.

Send us your drawing or project specification, and our engineers will confirm the assembly and quote within 24 hours.

For more fastening products, browse our full fastener catalog or check our blue white zinc plated eyelet bolt type B and carriage bolt DIN603 range.

发表评论

您的邮箱地址不会被公开。 必填项已用 * 标注

滚动至顶部