


A stainless steel flat washer is a thin, flat disc with a central hole placed under a bolt head or nut to spread the clamping load and protect the mating surface. This flat washer is made of stainless steel 304, sized for M10 bolts and nuts, and produced to DIN 125A / ISO 7089 with a natural finish. It is used in construction, machinery and furniture assemblies wherever a bolted joint needs a wider bearing surface and a clean, corrosion-resistant interface. Matched bolts and nuts are available together with the washer, and the standard minimum order is 10000 pieces per size.
What Is a Stainless Steel Flat Washer
A flat washer, also called a plain washer, is the simplest component in a bolted joint. It sits between the head of a bolt or the face of a nut and the surface being clamped, adding a flat bearing area that the fastener presses against. Unlike a spring washer or lock washer, a plain flat washer does not provide locking action; its role is load distribution, surface protection and spacing, not preventing the joint from loosening.
The washer passes over the bolt shank before the nut is tightened, and it keeps the rotating fastener face from scoring the workpiece as torque is applied. Because it is a standardised part, washers of the same standard and size can be selected to match the thread diameter, groove clearance and base material of the assembly.
Materials and Surface Finish
This washer is manufactured from stainless steel 304, a general-purpose austenitic stainless grade with good corrosion resistance in normal atmospheric, water and indoor service. The 304 material suits assemblies exposed to moisture, mild outdoor conditions or washdown environments where a plain carbon steel washer would rust.
The surface is a natural finish, without plating or coating. The plain stainless face keeps the washer free from added zinc or colour treatment, and it matches the appearance of other stainless fasteners in the same joint. For stronger chemical or salt-spray resistance, higher stainless grades can be discussed on request.
Dimensions and Standard: M10, DIN 125A / ISO 7089
The washer in this listing is sized for M10 bolt and nut thread, matching the M10 thread diameter through its inner bore. It follows the DIN 125A standard, the common metric normal-series plain washer specification, and corresponds to ISO 7089. The normal-series proportions keep a controlled outer diameter and thickness suited to general industrial bolting.
When ordering, specify the bolt size the washer will fit, together with the material and standard required. If the joint uses an oversized hole, a slotted hole or a thin soft substrate, a larger outer-diameter washer series may be more suitable, and we can advise the matching type. For reference on plain flat washer standards and load distribution, see this plain flat washer guide.
How the Washer Works in a Bolted Joint
In a tightened joint, the bolt or nut transfers clamp force through a small contact ring. Without a washer, that concentrated pressure can indent soft materials, pull through thin sheet, or scratch painted, coated or finished surfaces. The flat washer enlarges the bearing area, lowers the contact pressure on the workpiece and keeps the clamp load spread more evenly under the fastener face.
It also protects the mating surface while the nut or bolt turns during tightening, reducing gouging and fretting marks left by the rotating fastener. On irregular or slightly rough surfaces, the washer acts as a flat reference that improves torque repeatability, and it can bridge oversize or slotted holes so the fastener has a continuous bearing seat.
Applications
This stainless steel flat washer is used across construction, machinery and furniture assemblies, together with matching bolts and nuts. Common places include steel frames and brackets, machine bases and housings, timber and furniture joints, and general equipment where corrosion resistance and a clean stainless appearance are required.
Typical uses are under structural and machine bolt heads, under hex nuts on assembled frames, and wherever the clamped material is softer or more easily marked than the fastener itself. It pairs with hex bolts, carriage bolts and hex nuts in the same fastener set.
Custom Supply, MOQ and Lead Time
We supply flat washers by size, material and standard, and matched bolts and nuts can be supplied in the same order to keep the joint consistent.
- MOQ: 10000 pieces per size
- Matched bolts and nuts: available on request
- Sample: 3–7 days
- Bulk production lead time: 15–25 days
Marking and packing can be adjusted to your requirements, and trial quantities for common sizes can be arranged before bulk production.
Browse our related fasteners, including carriage bolts, structural hex bolts and stainless steel hex nuts for a complete bolted joint. Send your required bolt size and quantity for a flat washer quotation.