Hydraulic Back-up Ring (PTFE / Nylon)

hydraulic back-up ring PTFE nylon anti-extrusion ring for high pressure hydraulic O-ring seal

A hydraulic back-up ring is a rigid support ring fitted beside an elastomer O-ring in a hydraulic groove to block extrusion under high pressure. This hydraulic back-up ring is supplied in PTFE and nylon materials, placed on the low-pressure side of the O-ring to prevent the softer elastomer from flowing into the clearance gap between mating parts. It does not seal the fluid by itself; its role is to reinforce the O-ring so the seal can hold pressure without being squeezed or nibbled into the gap.

What Is a Hydraulic Back-up Ring

The hydraulic back-up ring belongs to the seal support group rather than the primary sealing group. In a cylinder joint, the O-ring provides the elastomeric contact that retains pressure, while the back-up ring stands behind it to carry the pressure-induced squeeze that would otherwise push the O-ring material into the diametral clearance. Where system pressure rises or the groove clearance is larger than the elastomer can tolerate, the back-up ring protects the O-ring from extrusion cuts, nibbling and premature failure.

A back-up ring is commonly installed on the low-pressure side of the O-ring groove. In reciprocating or bidirectional joints, back-up rings may be arranged on both sides so the O-ring is supported whichever way the pressure acts. The ring seats in the same groove alongside the O-ring and is checked during assembly that it lies flat without twisting, overlapping or rolling out of position.

Material: PTFE and Nylon

We supply the hydraulic back-up ring in two common materials:

  • PTFE: low friction and good chemical resistance, suitable for smooth sliding contact and general hydraulic service
  • Nylon: a harder thermoplastic with good strength and wear resistance, chosen where a rigid support and dimensional stability are required

PTFE back-up rings are valued for their smooth surface and compatibility with a wide range of hydraulic fluids, while nylon back-up rings offer a firm structural support in steady-duty high-pressure assemblies. The material choice depends on system pressure, fluid type, groove clearance and whether the application is static or reciprocating. For background on selecting anti-extrusion rings for pressure and clearance conditions, see this guide to back-up rings in high-pressure systems.

How It Prevents O-Ring Extrusion

Under pressure, an elastomer O-ring is squeezed toward the clearance between the housing and the moving piston or rod. Without support, the softer O-ring material flows into that gap, where repeated pressure cycles cut and nibble the seal lip until leakage develops. The hydraulic back-up ring fills the support space behind the O-ring and physically blocks the gap, giving the elastomer nowhere to extrude into.

This support spreads the pressure load across the O-ring rear face and keeps the seal cross-section seated in the groove. By holding the O-ring shape, the back-up ring helps retain a consistent seal contact face and reduces the chance of extrusion damage after pressure spikes or repeated cycles. Inspecting the O-ring and back-up ring together at maintenance intervals helps identify flattened, cracked or worn rings before they affect sealing.

Typical Applications

This hydraulic back-up ring is widely used in high-pressure hydraulic systems where O-rings must operate under elevated pressure or a wider than ideal clearance. Common equipment and circuits include:

  • High-pressure hydraulic cylinders and piston assemblies
  • Hydraulic valve blocks and manifold connections
  • Industrial hydraulic stations and power units
  • Mobile and construction machinery hydraulic circuits

It works as part of a matched seal assembly together with the O-ring and the other sealing elements in the cylinder. Related components in the same system include the hydraulic guide ring, which keeps the piston and rod aligned and carries side load, and the hydraulic cylinder seal kit, which covers the rod and piston sealing elements for a complete reseal.

MOQ and Custom Service

The minimum order quantity for this hydraulic back-up ring is 1000 pieces. We supply standard sizes matched to common O-ring grooves and can produce custom ring dimensions to your drawing or measured sample. OEM and ODM service is available, including custom material selection and packing to your project requirement.

Send us the O-ring size, groove dimensions, system pressure, fluid type and whether the joint is static or reciprocating, and our engineers will confirm the back-up ring material and size for your high-pressure hydraulic application.

Browse our full hydraulic seal range, including guide rings, piston seals, rod seals and wiper seals for construction machinery and industrial hydraulic systems.

发表评论

您的邮箱地址不会被公开。 必填项已用 * 标注

滚动至顶部