OO/OC Type Turnbuckle

oo oc type turnbuckle M6-M42 galvanized Q235 carbon steel eye and hook wire rope tensioner

An OO/OC type turnbuckle is an open-body rigging screw with opposite right-hand and left-hand threads, used to tension wire rope, cables and tie rods in construction, marine and rigging assemblies. This oo oc type turnbuckle is made from Q235 carbon steel with hot dip galvanized or electro galvanized finish, and it is available in thread sizes from M6 to M42. The OO version has an eye at each end, while the OC version has one eye and one hook, giving buyers a choice between a closed loop connection and a quick-hook connection.

What Is an OO/OC Type Turnbuckle

A turnbuckle, also called a rigging screw or bottle screw, consists of a threaded frame body with two end fittings that screw into opposite ends. Because the two threads are handed in opposite directions, rotating the frame body draws both fittings inward or pushes them outward, adjusting the overall length and removing slack from a cable, rod or guy wire. The open body leaves the threaded sections visible so tension and thread engagement can be checked during installation and inspection. This oo oc type turnbuckle suits both general rigging work and static cable tensioning where length adjustment is required.

The OO/OC designation describes the end fittings supplied in the same product range. The oo oc type turnbuckle range covers both eye-eye and eye-hook configurations, so buyers select the version that matches each anchor point. Buyers select the eye-eye version where both ends connect through a closed loop, or the eye-hook version where one end needs a faster hook-on connection. For a comparison of eye, hook and jaw end fittings, see this turnbuckle end fitting types and installation guide.

OO and OC End Fittings Explained

The OO turnbuckle, or eye-eye turnbuckle, carries a closed forged eye at both ends. Each eye accepts a shackle pin, an eye bolt, a pad eye or a chain link, giving a closed connection that cannot open under vibration or load reversal. It suits permanent and semi-permanent cable runs, stays, structural tie rods and marine rigging where both anchor points accept a loop connection.

The OC turnbuckle, or eye-hook turnbuckle, has an eye at one end and a hook at the other. The hook allows rapid connection and removal without tools, which is useful for temporary rigging, fencing and frequently reconfigured cable setups. In load-bearing service, the hook should be secured with a safety latch or seized with wire as required, and the fitting should not be used for overhead lifting unless it is specifically rated for that purpose. Select the oo oc type turnbuckle version according to whether each anchor point needs a closed eye or a quick hook.

Material and Surface Finish

This oo oc type turnbuckle is manufactured from Q235 carbon steel, a general structural carbon grade suited to static tensioning and general rigging duty. The steel frame and end fittings are supplied in two galvanized finishes to control corrosion:

  • Hot dip galvanized (HDG): a thick zinc coating for outdoor, coastal and corrosion-prone service
  • Electro galvanized (EG): a thinner zinc finish for lighter-duty, indoor and dry applications

The galvanized layer protects the carbon steel body and threads from rust and surface wear. For long-term marine exposure, the hot dip galvanized version is usually selected over the electro galvanized finish.

Sizes and Thread Range

The open-body oo oc type turnbuckle is offered in metric thread sizes from M6 to M42. The size refers to the thread diameter of the end fitting, and each size matches a frame length, rod capacity and take-up range. When ordering, specify the thread size, end fitting combination (OO or OC), finish and the anchor fittings at each end so the turnbuckle can be matched to the cable or rod it will tension.

How It Tensions a Wire Rope or Cable

To tension a wire rope or cable, both end fittings are first extended to allow maximum take-up after attachment. Before turning the frame, check that the oo oc type turnbuckle threads are clean and free of rust or damage. One end is connected to its anchor point, the other to the cable or rod, and the frame body is rotated to shorten the assembly until the required tension is reached. After adjustment, the thread engagement should be balanced at both ends and checked so the fitting is not run beyond its safe adjustment range.

Turnbuckles are static tensioning components for cables, stays and rods. They should be matched to the working load of the assembly, inspected for bent frames, cracked eyes, damaged threads or rusted fittings, and replaced if any defect is found.

Applications and Custom Supply

This oo oc type turnbuckle is widely used for wire rope tightening, construction, marine and rigging applications. Common setups include wire rope and cable railing systems, structural tie rods and guy wires, boat and dock rigging, fencing and gate bracing, curtain wall tension rods and general cable anchoring.

We supply open-body turnbuckles by size, end type and finish, and can match them with shackles, eye bolts and sling hooks for a complete rigging assembly. Custom marking and packing are available on request.

Browse our related rigging hardware, including G80 eye sling hooks for lifting and eye bolts for fixed anchor points. Send your required size, end type and finish for a turnbuckle quotation.

发表评论

您的邮箱地址不会被公开。 必填项已用 * 标注

滚动至顶部